Shop at Amazon.ca
Saturday, December 28, 2013
Temperature at which steel fails and babbitt melts
STEEL:
Steel is an alloy of iron and carbon.
Temperature Failure of Steel:
400 C (750 F) - structural steel starts losing yield strength
600 C (1112 F) - structural steel is 50% failed, steel expands and twists
800 C (1470 F) - ordinary construction steel is 90% failed
1000 C (1830 F) - carbon steel is 97% failed
1100 C (2012 F) - carbon steel is 100% failed, complete failure
Steel starts to become soft:
538 °C (1,000 °F)
Melting Point of Steel:
Carbon Steel: 1425 - 1540 Celsius
Carbon Steel: 2600 - 2800 Fahrenheit
Average Steel: 1400-1600 C depending on type of steel
Steel: 1370 degrees C (2500 °F)
BABBITT:
Babbitt is a metal alloy for bearing surfaces.
Babbitt is an alloy of 89% Tin, 8% Antimony and 3% Copper
Babbit fatigue strength failure temperature is: 130 C (265 ˚F)
Babbit melting temperature is: 238 C ( 460 ˚F )
Friday, December 27, 2013
Purpose of Gearbox in Ships
The function of gearbox in the ship:
- convert high speed, low torque rotation of prime mover (gas turbine, steam engine, diesel engine...)into
low speed, high torque rotation for use by the shaft and propeller
Why lower speed has higher torque?
- torque is the twisting force that causes rotationTORQUE = FORCE x DISTANCE
- the greater the distance, the greater the torque
- the greater the diameter of the gear, the greater the torque
- the greater the torque, the more power for lifting, moving or towing heavy loads of the ship
SPEED IS INVERSELY PROPORTIONAL TO DIAMETER OF GEAR
- the smaller the gear, the faster it turns
- the bigger the diameter of the gear, the slower it rotates
but from the torque equation:
- the bigger the diameter of the gear, the larger is the torque
therefore:
LOW SPEED HAS HIGH TORQUE
Why are low pressure turbine blades larger
Why low pressure turbines have larger blades?
Low Pressure (LP) turbine blades have longer length so that:
- more force can be extracted --> FORCE = PRESSURE * AREA of blades
- the steam pressure has been reduced after coming from the high pressure (HP) turbine, therefore, to extract more force, the blade area of the low pressure turbine has to be larger
- the more force, the more work
- the more work, the more power output
Why are high pressure turbine blades smaller?
HP turbine have shorter blade length because:
- ANGULAR VELOCITY inversely proportional to RADIUS
- the smaller the turbine blade diameter, the faster it rotates
- the smaller the blades, the faster it turns
- smaller blades can withstand the higher pressure and higher velocity of steam
- smaller blade lengths are more robust against torsional failure and vibrations
- smaller blades can maintain the higher velocity of the steam
FORCE = MASS * ACCELERATION
FORCE = MASS * VELOCITY / TIME
- higher velocity means higher impulse
- higher impulse means higher force
- higher force means higher work done
- higher work means higher energy transferred to the shaft
- higher energy extracted means higher power output
- higher power output means higher thermal efficiency
- higher thermal efficiency means higher savings
- higher savings means higher benefits
Thursday, December 26, 2013
Sequential Throttle Valve - partial arc admission
How does sequential throttle valve governor work? -partial arc admission
- valves lift off their seats in sequence
- valves open in sequential manner
- valves have preset lift clearances between stem nuts and the lift bar so that the length of the clearances are increasing
- valves with smaller clearance will fully open faster than valves with longer lift clearance
- shorter valves are lighter (lesser in weight) so they are raised first and then the longer, heavier valves
- the net effect is that valves are progressively opened to allow a sequential flow from the valves opening in sequenced order beginning with the smallest clearance to the largest clearance
- this design is commonly used for steam chest governor valve
Partial Arc Admission vs. Full Arc Admission - advantages & disadvantages:
- in partial arc admission, the greater the load, more valves will open to admit steam
- in partial arc admission, the lesser the load, fewer valves will open to admit steam
- partial arc admission: disadvantages = uneven heating of high pressure areas of turbine
- partial arc admission: advantages = more control on throttling the valves
- in full arc admission, all valves open at the same time
- in full arc admission, as the load increases, all the valves are more fully opened
- in full arc admission, as the load decreases, all the valves are less opened
- full arc admission: disadvantages = throttling loss in the valves
- full arc admission: advantages = more uniform heating around the high pressure part of turbine
Balance design of throttle governor:
- start with full arc and then switch to partial arc later in the operation process
Wednesday, December 25, 2013
Purpose of Journal Bearing
Function of Journal Bearings:
- to support radial loads in shafts, rotors
- to align and guide the rotating shaft
- to reduce friction
- to cushion radial motion of shaft (journal)
Features, Characteristics, Uses of Journal Bearings:
- type of plain bearing aka radial bearing, friction bearing, rotary bearing, sleeve bearing
- consists of the journal (shaft) and the bearing surface
- used in high power industrial machinery
- used in high load applications
- used in steam turbines, centrifugal pumps, centrifugal compressors
Purpose of Thrust Bearing:
- is a type of rotary bearing
- to support axial loads to the shaft
Tuesday, December 24, 2013
Purpose of Turbine Rotor and Stator
Purpose of Turbine Rotor:
- the rotor is the rotating (moving) part of the turbine
- the rotor is attached to the shaft
- the rotor receives the energy from the fluid causing the rotor to spin and the shaft to turn as well
- the function of the rotor is to extract the energy from the fluid and convert it to rotational energy
Purpose of Turbine Stator:
- the stator is the stationary (fixed) part of the turbine
- the stator is attached to the turbine casing
- the stator guides and changes the direction of the fluid from one rotor stage to another rotor stage
- the function of the stator is to redirect the flow of the fluid to the next rotor stage
Curtis turbine - how does it work
The principle of operation of a Curtis turbine:
- Curtis turbine is a type of impulse turbine
- curtis turbine has 2 sets of moving blades separated by 1 set of stationary blade
- rotating (moving) blades are attached to the turbine rotor
- fixed (stationary) blades are attached to the turbine casing
- Curtis turbine arrangement is as follows: (see picture)
a. nozzle
b. first set (ring) of moving blades ---> M
c. set of stationary (fixed) blades ----> F
d. second set of moving blades ------> M
Fig. 1. Curtis wheel turbine having 2 sets of rotating blades with
1 set of fixed blades in between. (by Subik Kumar):
- nozzle: converts high pressure energy of the steam into high velocity kinetic energy
- first ring of moving blades: gains momentum force and rotates while steam velocity is reduced
- set of fixed blades: guides the steam to flow with same velocity to the second set of moving blades
- second set of moving blades: rotates while steam velocity is reduced
- steam pressure is reduced through the nozzle only
- steam pressure remains the same after the nozzle as it passes through moving and fixed blades
- steam velocity is reduced after it passes through the moving blades
- steam velocity is constant as it passes through fixed blades
Subscribe to:
Posts (Atom)
